# Olimex UEXT-CH390 SPI to Ethernet module targets Raspberry Pi and ESP32 MCU boards running ESPHome

DevFeed: [Olimex UEXT-CH390 SPI to Ethernet module targets Raspberry Pi and ESP32 MCU boards running ESPHome](<https://devfeed.tech/articles/olimex-uext-ch390-spi-to-ethernet-module-targets-raspberry-pi-and-esp32-mcu-boards-running-esphome-120335.md>)

Original publisher: [Read original article](<https://www.cnx-software.com/2026/11/06/olimex-uext-ch390-spi-to-ethernet-module-targets-raspberry-pi-and-esp32-mcu-boards-running-esphome/>)

Author: Debashis Das

Published: 2026-11-06T02:48:49Z

Content type: news

Language: en

Sources: [CNX Software - Embedded Systems News](<https://devfeed.tech/sources/cnx-software-embedded-systems-news.md>)

Topics: [Ethernet](<https://devfeed.tech/topics/ethernet.md>), [esphome](<https://devfeed.tech/topics/esphome.md>), [ESP32](<https://devfeed.tech/topics/esp32.md>), [Embedded Software Dev](<https://devfeed.tech/topics/embedded-software-dev.md>), [Embedded Systems](<https://devfeed.tech/topics/embedded-systems.md>), [Home Assistant](<https://devfeed.tech/topics/home-assistant.md>), [ESP32-C3](<https://devfeed.tech/topics/esp32-c3.md>), [ESP32-C6](<https://devfeed.tech/topics/esp32-c6.md>), [ESP32-S3](<https://devfeed.tech/topics/esp32-s3.md>), [Arduino](<https://devfeed.tech/topics/arduino.md>)

Tags: [arduino](<https://devfeed.tech/tags/arduino.md>), [controller](<https://devfeed.tech/tags/controller.md>), [esp32](<https://devfeed.tech/tags/esp32.md>), [esphome](<https://devfeed.tech/tags/esphome.md>), [espressif](<https://devfeed.tech/tags/espressif.md>), [ethernet](<https://devfeed.tech/tags/ethernet.md>), [hardware](<https://devfeed.tech/tags/hardware.md>), [home-assistant](<https://devfeed.tech/tags/home-assistant.md>), [iot](<https://devfeed.tech/tags/iot.md>), [iot-sensors](<https://devfeed.tech/tags/iot-sensors.md>), [kicad](<https://devfeed.tech/tags/kicad.md>), [microcontroller](<https://devfeed.tech/tags/microcontroller.md>), [module](<https://devfeed.tech/tags/module.md>), [olimex](<https://devfeed.tech/tags/olimex.md>), [open-source](<https://devfeed.tech/tags/open-source.md>), [raspberry-pi](<https://devfeed.tech/tags/raspberry-pi.md>), [spi](<https://devfeed.tech/tags/spi.md>)

## AI overview

Olimex's UEXT-CH390 adds 10/100 Mbps Ethernet to microcontrollers over SPI, using the WCH CH390's integrated MAC and PHY so the host does not need its own Ethernet MAC. Unlike controllers with hardware TCP/IP offloading, the CH390 relies on the host MCU to process network protocols. The 50 x 21 mm module provides RJ45, UEXT and 1.0 mm-pitch pUEXT connectors, runs on 3.3 V, and supports SPI modes 0 and 3. ESPHome support is described for ESP32 devices, and Olimex has added an RP2040 driver tested on a Pico-compatible board with ESPHome 2026.9.0. That setup supports DHCP, Home Assistant discovery, Ethernet OTA updates after initial USB flashing, and a local web interface. Olimex also provides UF2 firmware and a separate Pico SDK example using lwIP.

## Source excerpt

Olimex UEXT-CH390 is a small open-source hardware module that adds 10/100 Mbps wired Ethernet connectivity to microcontroller boards through an SPI interface. It is designed for Raspberry Pi Pico and Pico 2 boards, as well as ESP32-S3, C3, C5, C6, and other microcontrollers without built-in Ethernet connectivity. The module is based on the WCH CH390 Ethernet controller and features an RJ45 connector, a standard UEXT connector, and a smaller 1.0mm-pitch pUEXT connector. It measures 50 x 21 mm and is supported in the Arduino IDE and ESPHome firmware, making it suitable for wired IoT sensors, Home Assistant devices, and other applications where WiFi is unreliable or unwanted. Olimex UEXT-CH390 specifications: Ethernet controller - WCH CH390 with integrated 10/100 Mbps Ethernet MAC and PHY 10BASE-T and 100BASE-TX Ethernet with auto-negotiation Auto-MDIX support for automatic cable detection Built-in 16KB SRAM for packet buffering Factory-programmed MAC address, eliminating the need for an external [...] The post Olimex UEXT-CH390 SPI to Ethernet module targets Raspberry Pi and ESP32 MCU boards running ESPHome appeared first on CNX Software - Embedded Systems News.