# Embedded Systems Published articles for Embedded Systems. This is one page of public article previews, not the complete archive. Follow Next page to continue. Summaries are not the original full articles. ## Raspberry Pi 5 gets dual GMSL2 Camera HAT based on MAX96716A deserializer DevFeed: [Raspberry Pi 5 gets dual GMSL2 Camera HAT based on MAX96716A deserializer]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-17T09:00:55Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [Raspberry Pi](), [webcam](), [Embedded Systems](), [Linux](), [contact-rich manipulation]() Tags: [automotive](), [broadcom-bcmxxxx](), [camera](), [computer-vision](), [debian](), [embedded-systems](), [hardware](), [linux](), [mipi-csi](), [raspberry-pi](), [raspberry-pi-5](), [robotics]() ### AI overview BE-IIS has released a dual GMSL2 Camera HAT for Raspberry Pi 5. Based on the MAX96716A deserializer, it connects two remote GMSL2 cameras through the board's CSI-2 interfaces and has been tested over 10-meter coaxial cables. ### Source excerpt BE-IIS (Brechel Electronic-Industrial Interface Systems) has released a dual GMSL2 Camera HAT for the Raspberry Pi 5. The board is based on the MAX96716A GMSL2 deserializer and connects two remote GMSL2 cameras through the Pi's CSI-2 interfaces. The solution has been validated in a dual-camera setup that operates at 2304 x 1296, RAW10, with two CSI-2 lanes per camera using the same Sony IMX708 12MP camera sensors found in the Raspberry Pi Camera Module 3. Besides low latency, one advantage of GMSL2 is long-range operation, and the HAT has been tested with two cameras connected over 10-meter coaxial cables. BE-IIS BE-IIS-2CAM (aka BE-IIS-GMSL2-2CAM) HAT+ specifications: Dual MIPI CSI camera output compatible with Raspberry Pi CSI interfaces Dual GMSL2 camera input 2x Rosenberger FAKRA connectors Up to 6 Gbps each PoC filter and protection per connector Analog Devices MAX96716A GMSL2 deserializer Misc Single and Dual HAT Operation 40-pin Raspberry Pi GPIO header [...] The post Raspberry Pi 5 gets dual GMSL2 Camera HAT based on MAX96716A deserializer appeared first on CNX Software - Embedded Systems News. ## ENILINX TICKEY - An ESP32-S3-based color e-Paper badge with open firmware (Crowdfunding) DevFeed: [ENILINX TICKEY - An ESP32-S3-based color e-Paper badge with open firmware (Crowdfunding)]() Original publisher: [Read original article]() Author: Debashis Das Published: 2026-09-17T00:00:34Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [ESP32-S3](), [e-ink](), [Microcontroller](), [Embedded Systems](), [Open Source]() Tags: [ble](), [bluetooth](), [display](), [e-paper](), [embedded](), [embedded-systems](), [epaper](), [esp32](), [esp32-s3](), [espressif](), [firmware](), [hardware](), [kickstarter](), [low-power](), [news](), [nfc](), [open-source](), [qr-code](), [screen](), [video]() ### AI overview ENILINX has launched the TICKEY, a 3.7-inch color e-paper badge and desk display based on the ESP32-S3. It includes Wi-Fi, Bluetooth, NFC, a rechargeable battery, and support for smartphone updates, with standard and Developer Edition storage options. The company describes the firmware as open source, but no repository or further implementation details were available when the article was written. ### Source excerpt ENIAC (operating as ENILINX) has launched the TICKEY, a 3.7-inch color e-Paper smart badge and desk display built around an ESP32-S3 MCU. The device features Wi-Fi, Bluetooth, and NFC connectivity, allowing users to update the screen from a smartphone without requiring continuous power to hold a static image. The display uses Modos' color e-paper technology to deliver 48+ native colors, with refresh times as fast as 3 seconds and sunlight readability. Measuring just 3.8mm thick and weighing 45 grams, TICKEY features an aluminum-alloy body and interchangeable faceplates, and supports NFC and QR code-based web profile sharing. The standard version includes 8MB of storage, whereas the Developer Edition offers 128MB for more advanced applications. These features make it suitable for desk reminders, event identification, digital business cards, and interactive maker projects. TICKEY specifications: Wireless MCU - ESP32-S3 Dual-core Tensilica LX7 microcontroller @ up to 240 MHz Wireless - 2.4 GHz 802.11n [...] The post ENILINX TICKEY - An ESP32-S3-based color e-Paper badge with open firmware (Crowdfunding) appeared first on CNX Software - Embedded Systems News. ## What to Expect at the Zephyr Project Workshop & Meetup (September 24, 2026) - Stuttgart, Germany DevFeed: [What to Expect at the Zephyr Project Workshop & Meetup (September 24, 2026) - Stuttgart, Germany]() Original publisher: [Read original article]() Author: Susan Remmert Published: 2026-09-16T17:57:36Z Content type: article Language: en Sources: [Zephyr Project]() Topics: [Embedded Systems](), [Open Source](), [Application Development](), [Testing](), [Simulation](), [Command-line interface]() Tags: [2026](), [blog](), [command-line](), [developers](), [embedded-systems](), [events](), [germany](), [meetup](), [open-source](), [technical](), [workshop](), [zephyr]() ### AI overview The Zephyr community will hold a hands-on workshop and afternoon meetup in Stuttgart, Germany, on September 24, 2026. The workshop will cover practical Zephyr development, while the meetup will feature community-led technical presentations and networking. ### Source excerpt On September 24, the Zephyr community will gather in Stuttgart for a hands-on workshop followed by an afternoon meetup featuring community-led technical presentations. The event is open to experienced contributors, first-time users, students, engineers, and anyone interested in open source embedded development. Attendees may join both sessions or choose either the workshop or the meetup based on their interests. ## What to Expect at the Zephyr Project Workshop & Meetup (September 24, 2026) - Stuttgart, Germany DevFeed: [What to Expect at the Zephyr Project Workshop & Meetup (September 24, 2026) - Stuttgart, Germany]() Original publisher: [Read original article]() Author: Susan Remmert Published: 2026-09-16T17:57:36Z Content type: news Language: en Sources: [Zephyr Project]() Topics: [Embedded Systems](), [Embedded Software Dev](), [Application Development](), [Testing](), [Simulation](), [Open Source]() Tags: [2026](), [blog](), [command-line](), [community](), [contributors](), [development](), [embedded](), [embedded-systems](), [event](), [events](), [germany](), [meetup](), [open-source](), [sessions](), [simulation](), [technical](), [testing](), [workshop](), [zephyr]() ### AI overview The Zephyr community will hold a hands-on workshop and afternoon meetup in Stuttgart, Germany, on September 24, 2026. The program includes guided exercises, technical presentations, community networking, and discussions of Zephyr-based embedded applications. ### Source excerpt On September 24, the Zephyr community will gather in Stuttgart for a hands-on workshop followed by an afternoon meetup featuring community-led technical presentations. The event is open to experienced contributors, first-time users, students, engineers, and anyone interested in open source embedded development. Attendees may join both sessions or choose either the workshop or the meetup based on their interests. ## OpenMANET - A higher-bandwidth Meshtastic alternative leveraging 802.11ah WiFi HaLow DevFeed: [OpenMANET - A higher-bandwidth Meshtastic alternative leveraging 802.11ah WiFi HaLow]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-16T07:00:04Z Content type: article Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [Open Source](), [Networks](), [Wi-Fi](), [Raspberry Pi](), [lora](), [networking](), [meshtastic](), [Embedded Systems]() Tags: [802-11ah](), [broadcom-bcmxxxx](), [camera](), [embedded-systems](), [gps](), [halow](), [hardware](), [linux](), [low-power](), [mesh-networking](), [meshtastic](), [network](), [open-source](), [openmanet](), [openwrt](), [raspberry-pi](), [seeed-studio]() ### AI overview This article introduces OpenMANET, an open-source long-range wireless mesh networking project using Raspberry Pi hardware and Wi-Fi HaLow chips. It compares OpenMANET with LoRa-based Meshtastic, noting higher bandwidth and features such as push-to-talk, GPS sharing, video streaming, and ATAK integration, alongside higher hardware cost and power consumption. ### Source excerpt OpenMANET is an open-source project for building long-range wireless mesh Mobile Ad-hoc Networks (MANETs) using Raspberry Pi SBCs and Wi-Fi HaLow (802.11ah) chips from Morse Micro. This came up when we wrote about Morse Micro USB WiFi HaLow adapters, and an X user commented that "OpenMANET is going to explode with these available, no more adapter boards or M.2 cards". OpenMANET targets search and rescue, disaster response, airsoft events, and other off-grid or infrastructure-failed situations. So it looks like an alternative to LoRa-based Meshtastic and Meshcore, with higher bandwidth, at the cost of more expensive hardware and higher power consumption. OpenMANET supports field communications, including push-to-talk, sharing GPS positions, cameras/video streams, and ATAK (Android Team Awareness Kit) integration. The mesh network can access the Internet through a single "mesh gate" over Starlink or cellular connectivity. The project supports a range of hardware platforms including Gateworks Venice, Raspberry Pi Zero 2 W, [...] The post OpenMANET - A higher-bandwidth Meshtastic alternative leveraging 802.11ah WiFi HaLow appeared first on CNX Software - Embedded Systems News. ## What to Expect at the Zephyr Project Meetup (September 19, 2026) - Buenos Aires, Argentina DevFeed: [What to Expect at the Zephyr Project Meetup (September 19, 2026) - Buenos Aires, Argentina]() Original publisher: [Read original article]() Author: Susan Remmert Published: 2026-09-15T22:12:26Z Content type: article Language: en Sources: [Zephyr Project]() Topics: [Embedded Systems](), [Open Source](), [Programming](), [amazon]() Tags: [2026](), [amazon](), [blog](), [community](), [embedded](), [embedded-systems](), [event](), [events](), [meetup](), [open](), [open-source](), [programming](), [software-development](), [zephyr]() ### AI overview The article announces an in-person Zephyr Project Meetup in Buenos Aires on September 19, 2026, organized by Iomico. It describes the event's audience, schedule, technical presentations, and a talk on integrating Amazon Sidewalk's closed protocol into a Zephyr application. ### Source excerpt The Zephyr Project community is heading to Buenos Aires, Argentina! Join us on Saturday, September 19, 2026, for an in-person Zephyr Project Meetup organized by Iomico. The event is open to developers, engineers, contributors, students, technology professionals, and anyone interested in open source, embedded systems programming, and software development. Whether you are an experienced Zephyr developer or are just beginning to explore embedded technologies, you are welcome to join. ## What to Expect at the Zephyr Project Meetup (September 19, 2026) - Buenos Aires, Argentina DevFeed: [What to Expect at the Zephyr Project Meetup (September 19, 2026) - Buenos Aires, Argentina]() Original publisher: [Read original article]() Author: Susan Remmert Published: 2026-09-15T22:12:26Z Content type: news Language: en Sources: [Zephyr Project]() Topics: [Embedded Systems](), [Open Source](), [Programming](), [Development]() Tags: [2026](), [blog](), [community](), [developers](), [embedded](), [embedded-systems](), [event](), [events](), [meetup](), [open-source](), [programming](), [software-development]() ### AI overview The Zephyr Project community will hold an in-person meetup in Buenos Aires on September 19, 2026, organized by Iomico. The event includes networking and technical presentations on Zephyr-based products, subsystems, development experiences, and integrating Amazon Sidewalk into a Zephyr application. ### Source excerpt The Zephyr Project community is heading to Buenos Aires, Argentina! Join us on Saturday, September 19, 2026, for an in-person Zephyr Project Meetup organized by Iomico. The event is open to developers, engineers, contributors, students, technology professionals, and anyone interested in open source, embedded systems programming, and software development. Whether you are an experienced Zephyr developer or are just beginning to explore embedded technologies, you are welcome to join. ## Alif Semi Balletto B1 and Ensemble E1C StartKits feature Cortex-M55 + Ethos-U55 MCU for IoT and Edge AI DevFeed: [Alif Semi Balletto B1 and Ensemble E1C StartKits feature Cortex-M55 + Ethos-U55 MCU for IoT and Edge AI]() Original publisher: [Read original article]() Author: Debashis Das Published: 2026-09-15T09:00:06Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [Microcontrollers](), [Embedded Systems](), [Microcontroller](), [cpu](), [Internet of things](), [Artificial Intelligence](), [SDK]() Tags: [802-15-4](), [ai](), [alif](), [ble](), [camera](), [core](), [debugger](), [development-board](), [devkit](), [edge](), [edge-ai](), [embedded-systems](), [hardware](), [i2c](), [iot](), [led](), [low-power](), [mcu](), [microcontrollers](), [mikrobus](), [open-source](), [sensor](), [specifications](), [testing](), [zephyr](), [zephyr-os]() ### AI overview Alif Semiconductor's Balletto B1 and Ensemble E1C StartKits are low-cost development boards built around Cortex-M55 microcontrollers with Ethos-U55 NPUs. The Balletto B1 adds BLE 5.3 and 802.15.4 connectivity, while both boards include camera, audio, sensor expansion, debugging, and power-measurement features. ### Source excerpt Alif Semiconductor's Ensemble E1C (SK-E1C) and Balletto B1 (SK-B1) StartKits are low-cost development boards built around the company's Cortex-M55 + Ethos-U55 microcontrollers. The Balletto B1 adds BLE 5.3 and 802.15.4 wireless connectivity, while the Ensemble E1C does not have built-in wireless connectivity. Both StartKits feature a microcontroller with a 160MHz Cortex-M55 CPU, an Ethos-U55 NPU, 2MB SRAM, and 1.8/1.9MB NVM. They also include an Arducam camera header, a mikroBUS Click Board expansion socket, and two PDM microphones for camera, audio, and sensor-based projects. The Balletto B1 additionally provides the complete RF path to a chip antenna for its wireless subsystem, while both boards feature an on-board Segger J-Link debugger for development and testing. Alif Semiconductor StartKit (SK-B1 and SK-E1C) specifications: MCU SK-E1C - Alif Semiconductor Ensemble E1C SK-B1 - Alif Semiconductor Balletto B1 CPU - Arm Cortex-M55 core with Helium-M Vector Extension @ up to 160 MHz NPU - Arm [...] The post Alif Semi Balletto B1 and Ensemble E1C StartKits feature Cortex-M55 + Ethos-U55 MCU for IoT and Edge AI appeared first on CNX Software - Embedded Systems News. ## JetKVM Mini - A low-cost, ESP32-P4X-based KVM with Ethernet or WiFi connectivity DevFeed: [JetKVM Mini - A low-cost, ESP32-P4X-based KVM with Ethernet or WiFi connectivity]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-14T02:03:40Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [Jetkvm](), [ESP32](), [Embedded Software Dev](), [Microcontroller](), [RISC-V](), [Web](), [WebRTC](), [networking](), [USB]() Tags: [4k](), [embedded-systems](), [esp-idf](), [esp32](), [esp32-p4](), [espressif](), [ethernet](), [firmware](), [freertos](), [github](), [hardware](), [hdmi](), [jetkvm](), [kvm](), [linux](), [macos](), [open-source](), [risc-v](), [soc](), [usb](), [video](), [webrtc](), [wifi](), [wifi-6]() ### AI overview JetKVM Mini is a smaller, lower-cost KVM over IP device based on the ESP32-P4X instead of Linux running on a Rockchip SoC. It provides Ethernet or WiFi connectivity, 1080p video capture, H.264 streaming over WebRTC, USB device emulation, and an information display. Its firmware uses FreeRTOS and ESP-IDF, while JetKVM OS Services add features such as 4K screen capture, shared clipboard, a guest terminal, and file transfer on compatible hosts. ### Source excerpt JetKVM Mini is a smaller, lower-cost version of the popular JetKVM KVM over IP solution. The new model features a small information display, offers Ethernet or WiFi connectivity, and supports 1080p video capture. The main under-the-hood change is that they ditched Linux on a Rockchip RV1106G3 SoC and now rely on an ESP32-P4X (ESP32-P4 version 3.x and greater) to handle video capture, H.264 encoding, USB, and other features. The largest cost saving is removing the RAM and eMMC flash required by Linux. JetKVM Mini specifications: SoC - Espressif Systems ESP32-P4X CPU Dual-core 32-bit RISC-V HP (High-performance) CPU @ up to 400 MHz with AI instruction extension and single-precision FPU Single-RISC-V LP (Low-power) MCU core @ up to 40 MHz Memory 768 KB HP L2MEM (for dual-core CPU), 32 KB LP SRAM, 8 KB TCM (for LP MCU core) 32 MB PSRAM Storage - 128 KB HP ROM, 16 KB LP ROM [...] The post JetKVM Mini - A low-cost, ESP32-P4X-based KVM with Ethernet or WiFi connectivity appeared first on CNX Software - Embedded Systems News. ## M5Stack Module13.2 LoRa-1262 expansion board integrates 14x10 mm Stamp LoRa-1262 module DevFeed: [M5Stack Module13.2 LoRa-1262 expansion board integrates 14x10 mm Stamp LoRa-1262 module]() Original publisher: [Read original article]() Author: Debashis Das Published: 2026-09-13T05:02:54Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [lora](), [systems]() Tags: [connectivity](), [development-board](), [embedded-systems](), [hardware](), [i2c](), [io](), [iot](), [lora](), [lorawan](), [low-power](), [lpwan](), [m5stack](), [module](), [news](), [power-management](), [routing](), [series](), [smart-agriculture](), [smart-city](), [spi](), [wireless]() ### AI overview M5Stack has launched the Stamp LoRa-1262 SMD module and the stackable Module13.2 LoRa-1262 expansion board for M5Stack Core controllers. Based on the Semtech SX1262, the module supports several modulation modes across 868-923 MHz, with up to +22 dBm transmit power and -147 dBm receive sensitivity. Module13.2 adds an RP-SMA antenna interface, M5IOE1 I/O expansion, configurable pin routing, and selectable I2C addresses for multi-module stacking. ### Source excerpt After launching the SX1262-based M5Stamp C6LoRa tiny module, M5Stack has launched two SX1262-based LoRa add-ons for the 868-923 MHz band: the tiny Stamp LoRa-1262 SMD module for custom PCBs, and the stackable Module13.2 LoRa-1262 module for the M5Stack Core series. The Stamp LoRa-1262 supports LoRa, FSK, GFSK, MSK, GMSK, and OOK modulation, with up to +22 dBm transmit power and -147 dBm receive sensitivity. The Module13.2 adds an RP-SMA antenna interface, an M5IOE1 IO expansion chip for reset and power management, and DIP switches for flexible pin routing and configurable I2C addresses, enabling multi-module stacking. Stamp LoRa-1262 SMD module M5Stack Stamp LoRa-1262 specifications: LoRa Transceiver - Semtech SX1262 Wireless Connectivity (LoRa) Frequency Band - 868 to 923 MHz Modulation Modes - LoRa, FSK, GFSK, MSK, GMSK, OOK Bitrate - Up to 300 kbps (programmable) Transmit power (Tx) - Up to +22 dBm Receive sensitivity (Rx) - Down to -147 dBm [...] The post M5Stack Module13.2 LoRa-1262 expansion board integrates 14x10 mm Stamp LoRa-1262 module appeared first on CNX Software - Embedded Systems News. ## EROFS Disables LZ4 Rolling Decompression Due To Data Corruption Possibility DevFeed: [EROFS Disables LZ4 Rolling Decompression Due To Data Corruption Possibility]() Original publisher: [Read original article]() Author: Michael Larabel Published: 2026-09-13T00:33:00Z Content type: news Language: en Sources: [Phoronix]() Topics: [Filesystems](), [systems](), [Optimization](), [Linux](), [data](), [Containers]() Tags: [containers](), [data](), [desktop-linux](), [embedded](), [embedded-systems](), [kernel](), [linux](), [linux-benchmarking](), [linux-hardware-benchmarks](), [linux-hardware-reviews](), [linux-how-to](), [linux-performance](), [linux-server-benchmarks](), [memory](), [open-source-graphics](), [optimization](), [phoronix](), [phoronix-test-suite](), [reduce](), [systems](), [ubuntu-benchmarks](), [ubuntu-hardware](), [x86]() ### AI overview EROFS has temporarily disabled LZ4 rolling decompression because a rare interaction with the upstream LZ4 implementation could produce corrupted data. The change prioritizes data correctness in production but increases runtime memory usage. ### Source excerpt The EROFS read-only file-system popular for embedded systems, containers, and other use-cases has resorted to temporarily disabling its LZ4 rolling decompression support due to data corruption concerns... ## NeoEyes NE302 - A tiny USB-C-powered WiFi 6 Edge AI Vision camera based on STM32N6 MCU DevFeed: [NeoEyes NE302 - A tiny USB-C-powered WiFi 6 Edge AI Vision camera based on STM32N6 MCU]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-12T02:19:36Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [Embedded Systems](), [Microcontroller](), [wifi 6](), [Hardware](), [object-detection]() Tags: [c-c-plus-plus](), [camera](), [computer-vision](), [edge-ai](), [embedded-systems](), [hardware](), [mcu](), [object-detection](), [open-source](), [stm32](), [stmicro-stm32](), [vision](), [wifi-6]() ### AI overview The article reports on CamThink's NeoEyes NE302, a compact USB-C-powered Wi-Fi 6 edge AI vision camera built around the STM32N6 MCU. It describes the device's reduced memory and feature set compared with the NE301, along with its camera, wireless, debugging, video-encoding, object-detection, networking, OTA, and security capabilities. ### Source excerpt CamThink NeoEyes NE302 is a tiny WiFi 6 Edge AI camera based on an STM32N6 Arm Cortex-M55 MCU with Neural-ART NPU which the company says is "especially suitable for developers and makers". I initially thought about it as a smaller version of the CamThink NeoEyes NE301 based on the same STM32N6 MCU and 4MP OS04C10 camera sensor. But it's quite a different device. First, it doesn't have a battery, and the USB-C is only used for power. Memory and storage capacities have been reduced to 32 MB PSRAM and 64 MP SPI flash, and a range of built-in and optional features have been removed, including 4G LTE module (global or US), audio wafers, PIR motion connector, and a 16-pin GPIO header, as well as support for PoE power. CamThink NeoEyes NE302 specifications: Vision MCU STMicro STM32N6 MCU Core - Arm 32-bit Cortex-M55 CPU @ up to 800MHz with Arm Helium [...] The post NeoEyes NE302 - A tiny USB-C-powered WiFi 6 Edge AI Vision camera based on STM32N6 MCU appeared first on CNX Software - Embedded Systems News. ## Renesas RZ/G3L & RZ/G3SE - Ultra-low-power Cortex-A55 MPUs for industrial HMI and IoT applications DevFeed: [Renesas RZ/G3L & RZ/G3SE - Ultra-low-power Cortex-A55 MPUs for industrial HMI and IoT applications]() Original publisher: [Read original article]() Author: Debashis Das Published: 2026-09-11T13:41:08Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [Embedded Systems](), [Hardware](), [Arm](), [cpu](), [Internet of things]() Tags: [arm](), [cortex-a55](), [cpu](), [development-board](), [devices](), [display](), [embedded-systems](), [gateway](), [h-264](), [hardware](), [hmi](), [industrial](), [iot](), [linux](), [low-power](), [medical-devices](), [real-time](), [renesas](), [renesas-mcu](), [smarc](), [systems](), [zephyr](), [zephyr-os]() ### AI overview Renesas introduced the RZ/G3L and RZ/G3SE, two 64-bit MPUs for HMI and IoT edge systems. Both use Arm Cortex-A55 application cores and an Arm Cortex-M33 real-time coprocessor. The RZ/G3L adds a Mali-G31 GPU and H.264 codec for richer HMI applications, while the RZ/G3SE targets IoT devices with basic display needs. Both support low-power standby operation. ### Source excerpt Renesas has expanded its RZ/G Series with the RZ/G3L and RZ/G3SE, two new 64-bit MPUs for HMI and IoT edge systems. Both devices integrate up to four Arm Cortex-A55 application cores clocked at up to 1.2 GHz and a 200 MHz Arm Cortex-M33 real-time coprocessor. The two chips are pin-to-pin compatible but target different applications. The RZ/G3L integrates an Arm Mali-G31 3D GPU and H.264 video codec for HMI applications like retail terminals and medical devices. The RZ/G3SE removes the GPU and video codec and is designed for IoT devices with basic display requirements, including EV chargers and industrial gateway devices. Both can reduce standby power consumption to around 1 mW and resume operation quickly from deep standby, which is useful for devices that need to remain connected while consuming very little power. Renesas RZ/G3L and RZ/G3SE specifications: MPU core CPU Quad-core or Dual-core Arm Cortex-A55 @ up to 1.2 [...] The post Renesas RZ/G3L & RZ/G3SE - Ultra-low-power Cortex-A55 MPUs for industrial HMI and IoT applications appeared first on CNX Software - Embedded Systems News. ## What to expect at the Zephyr Project Meetup (September 17, 2026) - Zurich, Switzerland DevFeed: [What to expect at the Zephyr Project Meetup (September 17, 2026) - Zurich, Switzerland]() Original publisher: [Read original article]() Author: Susan Remmert Published: 2026-09-10T05:00:25Z Content type: news Language: en Sources: [Zephyr Project]() Topics: [Embedded Systems](), [Open Source](), [Embedded Software Dev](), [Tooling](), [Artificial Intelligence]() Tags: [2026](), [blog](), [community](), [debugging](), [developer-tools](), [developers](), [embedded](), [embedded-systems](), [event](), [events](), [meetup](), [modem](), [networking](), [open-source](), [practical](), [switzerland](), [technical]() ### AI overview An announcement for the September 17, 2026, Zephyr Project Meetup in Zurich, Switzerland, organized by Zoi TechCon GmbH. The event will include presentations on Zephyr modem support, embedded applications, developer tools, hardware, and practical implementation experiences. ### Source excerpt The Zephyr Project community is heading to Zurich, Switzerland! Join us on Thursday, September 17, 2026, for an in-person Zephyr Project Meetup organized by Zoi TechCon GmbH. The meetup will take place at Westhive Kitchen, Hardturmstrasse 161, 8005 Zürich, Switzerland. The event is open to developers, engineers, contributors, students, technology professionals, and anyone interested in open source and embedded systems. ## What to expect at the Zephyr Project Meetup (September 17, 2026) - Zurich, Switzerland DevFeed: [What to expect at the Zephyr Project Meetup (September 17, 2026) - Zurich, Switzerland]() Original publisher: [Read original article]() Author: Susan Remmert Published: 2026-09-10T05:00:25Z Content type: news Language: en Sources: [Zephyr Project]() Topics: [Embedded Systems](), [Embedded Software Dev](), [Open Source](), [systems](), [Tooling](), [Software]() Tags: [2026](), [blog](), [community](), [developers](), [embedded](), [embedded-systems](), [event](), [events](), [hardware](), [meetup](), [open](), [open-source](), [software](), [software-engineer](), [switzerland](), [talk](), [technical](), [zephyr]() ### AI overview The Zephyr Project community will hold an in-person meetup in Zurich, Switzerland, on September 17, 2026. The event will include technical presentations, networking, and discussions about Zephyr development, hardware, developer tools, and embedded systems. ### Source excerpt The Zephyr Project community is heading to Zurich, Switzerland! Join us on Thursday, September 17, 2026, for an in-person Zephyr Project Meetup organized by Zoi TechCon GmbH. The meetup will take place at Westhive Kitchen, Hardturmstrasse 161, 8005 Zürich, Switzerland. The event is open to developers, engineers, contributors, students, technology professionals, and anyone interested in open source and embedded systems. ## LattePanda Mu Ultra Compute Module features Intel Core Ultra 5 226V/7 256V Lunar Lake CPU for AI workloads DevFeed: [LattePanda Mu Ultra Compute Module features Intel Core Ultra 5 226V/7 256V Lunar Lake CPU for AI workloads]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-10T02:25:10Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [Embedded Systems](), [Hardware](), [intel](), [cpu](), [GPU](), [ddr5](), [x86](), [SOC]() Tags: [2-5gbe](), [3dmark](), [artificial-intelligence-ai](), [benchmarks](), [cpu](), [ddr5](), [development-board](), [devkit](), [dfrobot](), [edge-ai](), [embedded-systems](), [geekbench](), [gpu](), [hardware](), [intel](), [intel-core](), [linux](), [lunar-lake](), [som](), [ubuntu](), [wifi-6](), [wifi-7](), [windows-11]() ### AI overview CNX Software reports on the LattePanda Mu Ultra, an x86 compute module using Intel Core Ultra 5 226V or Ultra 7 256V Lunar Lake processors with 16GB of memory. It targets robotics, industrial automation, portable instruments, and vision and edge AI applications, with up to 115 TOPS of stated AI performance. ### Source excerpt The LattePanda Mu Ultra is an x86 Compute Module powered by an Intel Core Ultra 5 226V or Ultra 7 256V Lunar Lake processor and equipped with 16GB of DDR5 memory. Offered in the same compact 69.6 x 60mm form factor as the earlier LattePanda Mu Alder Lake-N system-on-module (N100 or Core i3-N305), it delivers much higher performance, including up 115 TOPS of AI performance. Target applications include robotics, industrial automation, portable instruments, vision AI, and a range of Edge AI applications. LattePanda Mu Ultra Specifications: Lunar Lake SoC (one or the other) Intel Core Ultra 5 Processor 226V CPU - Octa-core processor up to 4.5 GHz GPU - 7x Xe-core Intel Arc 130V GPU up to 1.85 GHz AI - 40 TOPS Intel AI Boost; combined up to 97 TOPS Intel Core Ultra 7 Processor 256V CPU - Octa-core processor up to 4.8 GHz GPU - 8x Xe-core Intel Arc [...] The post LattePanda Mu Ultra Compute Module features Intel Core Ultra 5 226V/7 256V Lunar Lake CPU for AI workloads appeared first on CNX Software - Embedded Systems News. ## Arduino UNO Media Carrier adds MIPI CSI/DSI and audio connectors to UNO Q and VENTUNO Q boards DevFeed: [Arduino UNO Media Carrier adds MIPI CSI/DSI and audio connectors to UNO Q and VENTUNO Q boards]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-10T00:00:32Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [UNO Q](), [Arduino](), [Raspberry Pi](), [Hardware](), [Open Source]() Tags: [arduino](), [audio](), [camera](), [connectors](), [display](), [embedded-systems](), [hardware](), [linux](), [mipi](), [mipi-csi](), [news](), [open-source](), [single-board-computer](), [specifications](), [touchscreen](), [uno-q](), [ventuno-q](), [waveshare]() ### AI overview The Arduino UNO Media Carrier adds accessible 22-pin MIPI DSI and CSI connectors, three 3.5 mm audio jacks, and RGB LEDs to Arduino UNO Q and VENTUNO Q boards. It is listed at $19.25 or EUR 19.89 including VAT. ### Source excerpt Arduino UNO Media Carrier board adds three audio jacks, a MIPI DSI display connector, two MIPI CSI camera connectors, and a few RGB LEDs to the Arduino UNO Q and Arduino VENTUNO Q SBCs. Both Arduino "Q" boards already expose MIPI CSI/DSI and audio interfaces, but only through the JMEDIA and JMISC 60-pin headers, which aren't very convenient. The Arduino UNO Media Carrier board fixes that with 22-pin MIPI connectors and 3.5 audio jacks. Arduino UNO Media Carrier (ASX00083) specifications: Compatible SBCs - Arduino UNO Q and Arduino VENTUNO Q Display I/F - 22-pin MIPI DSI connector compatible with standard MIPI-DSI display modules (5-inch, 8-inch, 10.1-inch Waveshare touch display compatible) Camera I/F - 2x 22-pin MIPI-CSI connectors compatible with IMX219 camera modules like the Raspberry Pi Camera Module 2 Audio 3.5 mm (MIC-IN/Headphones Out) audio jack 3.5mm Line Out audio jack 3.5mm Ear Out audio jack Host interfaces 60-pin female [...] The post Arduino UNO Media Carrier adds MIPI CSI/DSI and audio connectors to UNO Q and VENTUNO Q boards appeared first on CNX Software - Embedded Systems News. ## ESP32-C5 Pico board follows Raspberry Pi Pico form factor, ships with on-board or external antenna DevFeed: [ESP32-C5 Pico board follows Raspberry Pi Pico form factor, ships with on-board or external antenna]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-09T07:00:50Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [ESP32-C5](), [Raspberry Pi](), [Espressif](), [cpu](), [RISC-V](), [SOC](), [Bluetooth](), [wifi 6](), [zigbee](), [Matter](), [Embedded Systems](), [ESP-IDF]() Tags: [802-15-4](), [arduino](), [battery](), [ble](), [bluetooth](), [bluetooth-le](), [boot](), [c-c-plus-plus](), [development-board](), [embedded-systems](), [esp-idf](), [esp32](), [esp32-c5](), [espressif](), [gpio](), [hardware](), [iot](), [matter](), [news](), [port](), [raspberry-pi](), [risc-v](), [thread](), [usb](), [waveshare](), [wifi-6](), [zigbee]() ### AI overview The Waveshare ESP32-C5 Pico is a development board in the Raspberry Pi Pico form factor. It uses an ESP32-C5-MINI-1 series module with a RISC-V processor, dual-band WiFi 6, Bluetooth LE, and 802.15.4 support for Zigbee, Thread, and Matter. The board includes GPIO headers, USB-C, buttons, LEDs, and Li-Ion battery support, with variants offering PCB or external antennas. ### Source excerpt Waveshare ESP32-C5 Pico board brings the ESP32-C5 dual-band WiFi 6, Bluetooth LE, and 802.15.4 (Zigbee/Thread) SoC to the Raspberry Pi Pico form factor. The board features an ESP32-C5-MINI-1 Series module with PCB or external antenna, two 20-pin GPIO headers, a USB-C port for power and programming, Reset and Boot buttons, and a few LEDs. It also supports Li-Ion battery charging and discharging. Waveshare ESP32-C5 Pico specifications: Wireless module - ESP32-C5-MINI-1 or ESP32-C5-MINI-1U Wireless MCU - Espressif Systems ESP32-C5HF4 CPU Single-core 32-bit RISC-V processor @ up to 240 MHz Low-power RISC-V core @ 48 MHz acting as the main processor for power-sensitive applications Memory - 384 KB SRAM on-chip Storage - 320 KB ROM, 4MB SPI flash Wireless Dual-band (2.4/5 GHz) 802.11ax WiFi 6, 802.11b/g/n WiFi 4 backward compatibility WiFi modes: Station mode, SoftAP mode, SoftAP + Station mode, and promiscuous mode Bluetooth 5.0 Low Energy (LE) with Mesh support, up [...] The post ESP32-C5 Pico board follows Raspberry Pi Pico form factor, ships with on-board or external antenna appeared first on CNX Software - Embedded Systems News. ## What to expect at the Zephyr Project Meetup (September 15, 2026) - Amsterdam, Netherlands DevFeed: [What to expect at the Zephyr Project Meetup (September 15, 2026) - Amsterdam, Netherlands]() Original publisher: [Read original article]() Author: Susan Remmert Published: 2026-09-09T05:00:04Z Content type: article Language: en Sources: [Zephyr Project]() Topics: [Zephyr RTOS](), [Embedded Systems](), [Open Source](), [Fuzzing/Fuzz testing](), [simulator](), [developer tooling]() Tags: [2026](), [blog](), [bugs](), [community](), [contributors](), [embedded](), [embedded-systems](), [event](), [events](), [firmware](), [fuzzing](), [harness](), [meetup](), [open-source](), [simulator](), [talk](), [technologies](), [tooling](), [tools](), [zephyr]() ### AI overview The Zephyr Project Meetup in Amsterdam on September 15, 2026, will bring together embedded developers, contributors, students, and engineers to exchange practical knowledge about Zephyr RTOS. The agenda includes talks on JetBrains' work with Zephyr, fuzzing Zephyr applications with AFL and Renode, and making hardware development easier with Schematik. ### Source excerpt What are developers in the Netherlands building with Zephyr? On September 15, the embedded community will meet in Amsterdam to exchange practical knowledge, discuss current work, and learn more about the Zephyr RTOS. The event is open to experienced contributors, first-time users, students, engineers, and anyone curious about open source embedded development. ## What to expect at the Zephyr Project Meetup (September 15, 2026) - Amsterdam, Netherlands DevFeed: [What to expect at the Zephyr Project Meetup (September 15, 2026) - Amsterdam, Netherlands]() Original publisher: [Read original article]() Author: Susan Remmert Published: 2026-09-09T05:00:04Z Content type: news Language: en Sources: [Zephyr Project]() Topics: [Zephyr RTOS](), [Embedded Systems](), [Fuzzing/Fuzz testing](), [Open Source]() Tags: [2026](), [blog](), [c](), [c-plus-plus](), [crashes](), [developer-tooling](), [embedded](), [embedded-systems](), [event](), [events](), [firmware](), [fuzzing](), [harness](), [jetbrains](), [meetup](), [memory-corruption](), [open-source](), [simulator](), [zephyr]() ### AI overview The Zephyr Project Meetup in Amsterdam on September 15, 2026, will bring together embedded developers, contributors, students, and engineers to share practical knowledge about Zephyr RTOS. The agenda includes talks on JetBrains' work with Zephyr, fuzzing Zephyr with AFL and Renode, and making hardware development easier with Schematik. ### Source excerpt What are developers in the Netherlands building with Zephyr? On September 15, the embedded community will meet in Amsterdam to exchange practical knowledge, discuss current work, and learn more about the Zephyr RTOS. The event is open to experienced contributors, first-time users, students, engineers, and anyone curious about open source embedded development. ## Arm CSS for Mobile 2 "AI-Native" platform: Arm C2-Ultra and C2-Pro CPU cores, Mali G2-Ultra NX GPU DevFeed: [Arm CSS for Mobile 2 "AI-Native" platform: Arm C2-Ultra and C2-Pro CPU cores, Mali G2-Ultra NX GPU]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-08T02:52:39Z Content type: article Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [Arm](), [cpu](), [Artificial Intelligence](), [GPU](), [Embedded Systems]() Tags: [ai](), [arm](), [armv9](), [artificial-intelligence-ai](), [benchmarks](), [cpu](), [embedded-systems](), [gpu](), [laptop](), [processors](), [smartphone]() ### AI overview Arm introduced the CSS for Mobile 2 platform, combining C2-Ultra and C2-Pro CPUs with SME2 units and the Mali G2-Ultra NX GPU with dedicated neural accelerators. The article covers their specifications and Arm's claimed performance improvements over the previous C1 generation. ### Source excerpt Arm has introduced the CSS for Mobile 2 platform as an AI-native compute foundation comprised of the Arm C2-Ultra and C2-Pro CPUs with SME2 (Scalable Matrix Extension 2) units and the Mali G2-Ultra NX GPU with dedicated neural accelerators that enable neural graphics to run natively on the GPU. Arm C2-Ultra and C2-Pro CPUs Arm C2-Ultra specifications: Architecture - Armv9.3-A Extensions Armv9.4-A (Some key features) SME2 Extensions SVE2 Extensions Cryptography Extensions RAS Extensions ISA support - AArch64 Microarchitecture Pipeline - Out-of-order Superscalar Neon and SVE2 Optional Cryptography Unit Up to 14x CPUs in cluster 40-bit Physical Addressing Memory System and External Interfaces 64KB (I-Cache), 128KB (D-Cache) 2MB or 3MB L2 Cache Optional, 256KB to 32MB L3 Cache ECC Support Bus interfaces - AMBA AXI5 or CHI.E Optional ACP Optional Peripheral Port Security - TrustZone, Secure-EL2 Interrupts - GIC interface, GICv4.1 PMU - PMUv3 CoreSight - CoreSightv3 Embedded Trace Extension - [...] The post Arm CSS for Mobile 2 "AI-Native" platform: Arm C2-Ultra and C2-Pro CPU cores, Mali G2-Ultra NX GPU appeared first on CNX Software - Embedded Systems News. ## YuzukiNeko - A Linux-capable Allwinner F101 RISC-V SBC with Raspberry Pi Pico form factor DevFeed: [YuzukiNeko - A Linux-capable Allwinner F101 RISC-V SBC with Raspberry Pi Pico form factor]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-07T17:01:57Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [Raspberry Pi](), [Linux](), [RISC-V](), [Hardware](), [SOC](), [Embedded Systems](), [Open Source](), [Kernel](), [Software]() Tags: [allwinner](), [allwinner-d-series](), [buildroot](), [cpu](), [embedded-systems](), [gpio](), [hardware](), [linux](), [linux-7-x](), [mipi](), [open-source](), [psram](), [raspberry-pi](), [risc-v](), [single-board-computer](), [specifications](), [spi](), [storage](), [usb](), [zephyr](), [zephyr-os]() ### AI overview YuzukiHD has introduced YuzukiNeko, a Raspberry Pi Pico-sized open-source single-board computer built around the Allwinner F101 RISC-V SoC. It includes a 1.008 GHz C907 core, 8MB or 16MB PSRAM, SPI NOR flash, microSD storage, USB-C, and GPIO expansion, with support for Linux, Buildroot, and Zephyr RTOS. ### Source excerpt YuzukiHD has made another open-source hardware Linux SBC. YuzukiNeko is a Raspberry Pi Pico-sized single board computer powered by a new Allwinner F101 RISC-V SoC. The Allwinner F101 processor features a single 1.008 GHz C907 RISC-V core, 8MB or 16 MB PSRAM, and support for various display interfaces such as MIPI DSI, 24-bit RGB, and LVDS. The YuzukiNeko board itself features the F101 SoC, an SPI NOR flash, a microSD card for storage, a USB-C port, and two 20-pin GPIO headers. YuzukiNeko specifications: SoC - Allwinner F101 CPU - T-head C907 RISC-V core up to 1.008 GHz Memory - 8MB or 16MB PSRAM @ 252 MHz Package - QFN-68 Storage 128 Mbit NOR flash (PY25Q128HA-SUH-IT) MicroSD card slot USB - USB Type-C port for data, power, and programming Expansion 2x 20-pin expansion headers with GPIOs, ADC, 5V, 3.3V, and GND 5x pads with HP out (analog speaker output) and four [...] The post YuzukiNeko - A Linux-capable Allwinner F101 RISC-V SBC with Raspberry Pi Pico form factor appeared first on CNX Software - Embedded Systems News. ## XIAO SAMD21 Plus and RP2040 Plus USB-C boards get additional GPIO pins, integrated Li-ion battery management DevFeed: [XIAO SAMD21 Plus and RP2040 Plus USB-C boards get additional GPIO pins, integrated Li-ion battery management]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-07T01:07:22Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [Embedded Systems](), [Microcontroller](), [USB](), [Raspberry Pi]() Tags: [arm](), [atmel-samd](), [battery](), [boot](), [circuitpython](), [development-board](), [embedded-systems](), [gpio](), [hardware](), [i2c](), [led](), [mcu](), [micropython](), [raspberry-pi](), [rust](), [seeed-studio](), [software](), [usb](), [zephyr](), [zephyr-os]() ### AI overview Seeed Studio has expanded its XIAO Plus Series with the XIAO SAMD21 Plus and XIAO RP2040 Plus USB-C boards. The boards retain the existing form factor while adding GPIO pins and integrated Li-ion battery management, and support several embedded development platforms. ### Source excerpt Seeed Studio has expanded its XIAO Plus Series introduced in 2025, with the XIAO SAMD21 Plus and XIAO RP2040 Plus USB-C boards adding several GPIOs and integrated Li-ion battery management to the XIAO (SAMD21) and XIAO RP2040, launched in 2020 and 2021, respectively, while keeping the same form factor. XIAO SAMD21 Plus Specifications: MCU - Microchip SAMD21G18 Arm Cortex-M0+ microcontroller at up to 48MHz with 256KB Flash,32KB SRAM USB - 1x USB Type-C port for power and programming Expansion I/Os 2x 7-pin "legacy" headers with 11x analog inputs, 11x digital I/Os, 1x DAC, SPI, UART, and I2C Castellated holes and pads with 16x digital I/Os, I2C,and I2S 3.3V I/O voltage (not 5V tolerant) Misc Reset and Boot buttons RGB LED Charge LED Power Supply 5V via USB-C port Pads for battery On-board PMIC Dimensions - 23.5x17.5 mm Temperature Range - -40°C ~ 85°C The upgraded variant of the XIAO SAMD21 [...] The post XIAO SAMD21 Plus and RP2040 Plus USB-C boards get additional GPIO pins, integrated Li-ion battery management appeared first on CNX Software - Embedded Systems News. ## Strengthening Camera Support in Zephyr for Advanced Vision Applications DevFeed: [Strengthening Camera Support in Zephyr for Advanced Vision Applications]() Original publisher: [Read original article]() Author: Zephyr Project Published: 2026-09-04T21:12:17Z Content type: article Language: en Sources: [Zephyr Project]() Topics: [Embedded Systems](), [Embedded Software Dev](), [Open Source](), [Framework](), [Artificial Intelligence](), [object-detection](), [real-time](), [Streaming](), [Robotics]() Tags: [ai](), [blog](), [cameras](), [development](), [embedded](), [embedded-systems](), [events](), [india](), [industry-conference](), [object-detection](), [open-source](), [open-source-summit](), [real-time](), [robotics](), [streaming](), [vision](), [zephyr](), [zero-copy]() ### AI overview This event recap examines proposed changes to Zephyr's camera and driver architecture for AI-driven vision workloads. The proposals include attaching metadata and inference results to individual video buffers and adding per-buffer callbacks to improve buffer ownership, reduce CPU wakeups, and support more manageable camera pipelines. The changes remain under exploration through prototypes and community discussions. ### Source excerpt The Zephyr community came together at Open Source Summit India 2026 in Mumbai to share knowledge and explore developments, tooling, and real-world applications across embedded systems. In this second post event blog, we recap two lightning talks from the Zephyr track focused on camera support. [Next page]()