# webcam A camera device whose preview stream and captured photos or video can be accessed by software. This is one page of public article previews, not the complete archive. Follow Next page to continue. Summaries are not the original full articles. ## Raspberry Pi 5 gets dual GMSL2 Camera HAT based on MAX96716A deserializer DevFeed: [Raspberry Pi 5 gets dual GMSL2 Camera HAT based on MAX96716A deserializer]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-17T09:00:55Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [Raspberry Pi](), [webcam](), [Embedded Systems](), [Linux](), [contact-rich manipulation]() Tags: [automotive](), [broadcom-bcmxxxx](), [camera](), [computer-vision](), [debian](), [embedded-systems](), [hardware](), [linux](), [mipi-csi](), [raspberry-pi](), [raspberry-pi-5](), [robotics]() ### AI overview BE-IIS has released a dual GMSL2 Camera HAT for Raspberry Pi 5. Based on the MAX96716A deserializer, it connects two remote GMSL2 cameras through the board's CSI-2 interfaces and has been tested over 10-meter coaxial cables. ### Source excerpt BE-IIS (Brechel Electronic-Industrial Interface Systems) has released a dual GMSL2 Camera HAT for the Raspberry Pi 5. The board is based on the MAX96716A GMSL2 deserializer and connects two remote GMSL2 cameras through the Pi's CSI-2 interfaces. The solution has been validated in a dual-camera setup that operates at 2304 x 1296, RAW10, with two CSI-2 lanes per camera using the same Sony IMX708 12MP camera sensors found in the Raspberry Pi Camera Module 3. Besides low latency, one advantage of GMSL2 is long-range operation, and the HAT has been tested with two cameras connected over 10-meter coaxial cables. BE-IIS BE-IIS-2CAM (aka BE-IIS-GMSL2-2CAM) HAT+ specifications: Dual MIPI CSI camera output compatible with Raspberry Pi CSI interfaces Dual GMSL2 camera input 2x Rosenberger FAKRA connectors Up to 6 Gbps each PoC filter and protection per connector Analog Devices MAX96716A GMSL2 deserializer Misc Single and Dual HAT Operation 40-pin Raspberry Pi GPIO header [...] The post Raspberry Pi 5 gets dual GMSL2 Camera HAT based on MAX96716A deserializer appeared first on CNX Software - Embedded Systems News. ## Meta Reportedly Building Smart Glasses without Cameras Following Public Backlash DevFeed: [Meta Reportedly Building Smart Glasses without Cameras Following Public Backlash]() Original publisher: [Read original article]() Author: Scott Hayden Published: 2026-09-16T12:49:39Z Content type: news Language: en Sources: [Road to VR]() Topics: [Meta](), [webcam](), [Android XR]() Tags: [cameras](), [meta](), [news](), [privacy](), [xr-industry-news]() ### AI overview A report says Meta is preparing camera-less smart glasses, internally codenamed Luna, potentially for unveiling at its September Connect developer conference. The glasses are expected to use microphones, speakers, and a button for Meta AI instead of outward-facing cameras, amid privacy scrutiny of smart glasses. ### Source excerpt Meta is reportedly preparing a new slate of smart glasses that are ditching those pesky cameras. The News Zuckerberg previously teased a pair of smart glasses in May alongside the official announcement of Connect's September dates. Now, according to a report from The Information, those may be a new class of camera-less smart glasses, slated [...] The post Meta Reportedly Building Smart Glasses without Cameras Following Public Backlash appeared first on Road to VR. ## A puppet-themed cyberdeck built with Arduino UNO Q DevFeed: [A puppet-themed cyberdeck built with Arduino UNO Q]() Original publisher: [Read original article]() Author: Arduino Team Published: 2026-09-15T17:29:23Z Content type: article Language: en Sources: [Arduino Blog]() Topics: [Arduino](), [UNO Q](), [Bluetooth](), [USB](), [hdmi](), [webcam]() Tags: [arduino](), [bluetooth](), [creative](), [cyberdeck](), [cyberdecks](), [hdmi](), [personalization](), [puppet](), [uno-q](), [usb](), [webcam]() ### AI overview Natasha Dzurny built a portable cyberdeck around an Arduino UNO Q and designed it as an Avenue Q-style puppet. The build includes a Bluetooth keyboard and touchpad, USB battery pack, HDMI display, and a concealed USB webcam, with a fur-covered puppet head serving as the enclosure. ### Source excerpt The heart of the entire cyberdeck movement is personalization. Instead of shopping within the limits of what manufacturers deem to be marketable, cyberdeck builders can create designs that reflect their own personal tastes. But even so, most cyberdecks fit within a fairly narrow aesthetic--usually some variation of cyberpunk or cassette futurism, fitting the original Gibson [...] The post This cyberdeck is a... puppet? appeared first on Arduino Blog. ## Turn Arduino® UNO™ Q into your local 3D printing watchdog DevFeed: [Turn Arduino® UNO™ Q into your local 3D printing watchdog]() Original publisher: [Read original article]() Author: Arduino Team Published: 2026-09-14T18:03:45Z Content type: article Language: en Sources: [Arduino Blog]() Topics: [Arduino](), [Hardware](), [webcam](), [MQTT](), [Home Assistant](), [API](), [Security]() Tags: [3d-printer](), [3d-printer-watchdog](), [3d-printing](), [3d-printing-watchdog](), [anomaly-detection](), [api](), [arduino](), [cameras](), [edge-ai](), [hardware](), [mqtt](), [privacy](), [security](), [uno-q]() ### AI overview This Arduino Blog article presents a local 3D-printing watchdog built with an Arduino UNO Q, a camera, and the FOMO-AD anomaly model through Arduino App Lab. It trains on images of normal prints, flags deviations, and can automatically pause a print through the Moonraker API after repeated anomaly detections. The system can also integrate with OctoPrint, send MQTT notifications to Home Assistant, and operate entirely on the local network for privacy and security. ### Source excerpt A lot of newer 3D printers incorporate sophisticated sensor suites and cameras to detect problems with print jobs, like the dreaded "spaghetti failure." Those work pretty well and prevent wasted time, wasted filament, and even damage to the printer. But what if you don't have a printer with those features? Or if you want to [...] The post Turn Arduino® UNO™ Q into your local 3D printing watchdog appeared first on Arduino Blog. ## The Reflexes Machine turns a reaction game into an interactive experience DevFeed: [The Reflexes Machine turns a reaction game into an interactive experience]() Original publisher: [Read original article]() Author: Arduino Team Published: 2026-09-09T12:37:27Z Content type: article Language: en Sources: [Arduino Blog]() Topics: [Arduino](), [UNO Q](), [Computer vision](), [webcam](), [real-time](), [Hardware]() Tags: [architecture](), [arduino](), [building](), [camera](), [computer-vision](), [hardware](), [i2c](), [led](), [modulino-nodes](), [project](), [reaction-game](), [real-time](), [reflex-game](), [reflexes-machine](), [sensors](), [uno-q]() ### AI overview An Arduino community member built Reflexes Machine, an arcade-style reaction game using an Arduino UNO Q board, Modulino nodes, a USB camera, illuminated buttons, LED Matrix displays, and sound effects. The camera detects a player's face and automatically starts the countdown. ### Source excerpt What happens when you combine a little imagination with a powerful dual-brain board and a handful of building-block sensors? In the case of Arduino community member LucaDilo, you get a reaction game that doesn't simply wait for someone to press a button... it actually notices when you walk up and invites you to play. Reflexes [...] The post The Reflexes Machine turns a reaction game into an interactive experience appeared first on Arduino Blog. ## ArduinoCore-Zephyr 1.0.0 adds support for Arduino VENTUNO Q, updates to Zephyr 4.4.1, and more DevFeed: [ArduinoCore-Zephyr 1.0.0 adds support for Arduino VENTUNO Q, updates to Zephyr 4.4.1, and more]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-04T10:27:38Z Content type: release Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [Arduino](), [Zephyr RTOS](), [Embedded Systems](), [Embedded Software Dev](), [Hardware](), [Microcontroller](), [webcam](), [ci]() Tags: [arduino](), [bug-fixes](), [camera](), [ci](), [development-board](), [embedded-systems](), [hardware](), [mcu](), [real-time](), [release](), [software-management](), [ventuno-q](), [vision](), [zephyr](), [zephyr-os]() ### AI overview Arduino has released ArduinoCore-Zephyr 1.0.0 with support for the VENTUNO Q SBC and Nicla Vision camera, an update to Zephyr 4.4.1, and bug-fix and CI improvements. The article also lists supported Arduino platforms and installation steps. ### Source excerpt Arduino has just announced the release of ArduinoCore-Zephyr version 1.0.0, with new hardware support, including the VENTUNO Q SBC, an updated Zephyr 4.4.1 base, support for the Nicla Vision camera, and various fixes and improvements. Arduino first announced its plans to switch from Arm Mbed to Zephyr RTOS in July 2024, before releasing the first beta of Arduino Core for Zephyr in December of the same year. ArduinoCore-Zephyr 1.0.0 is not the first stable version, since that was version 0.90.0 released on July 29, 2026. The new release builds on that, so let's see what's new. ArduinoCore-Zephyr 1.0.0 highlights Support for Arduino VENTUNO Q SBC, specifically the STM32H5F5 real-time MCU on the board Update to Zephyr 4.4.1 with the latest upstream improvements, security fixes, and driver support Added Nicla Vision camera support to capture and process image data directly through the Zephyr core Various bug fixes and CI improvements Currently [...] The post ArduinoCore-Zephyr 1.0.0 adds support for Arduino VENTUNO Q, updates to Zephyr 4.4.1, and more appeared first on CNX Software - Embedded Systems News. ## Circuit Valley CHC5 - A modular USB, HDMI, and Ethernet camera system (Crowdfunding) DevFeed: [Circuit Valley CHC5 - A modular USB, HDMI, and Ethernet camera system (Crowdfunding)]() Original publisher: [Read original article]() Author: Jean-Luc Aufranc (CNXSoft) Published: 2026-09-02T07:25:10Z Content type: news Language: en Sources: [CNX Software - Embedded Systems News]() Topics: [webcam](), [Hardware](), [USB](), [hdmi](), [Ethernet](), [SOC](), [Embedded Systems](), [Linux](), [SDK](), [Open Source]() Tags: [arm](), [buildroot](), [c-c-plus-plus](), [camera](), [computer-vision](), [edge-ai](), [embedded-systems](), [ethernet](), [fpga](), [hardware](), [hdmi](), [kickstarter](), [linux](), [open-source](), [poe](), [sdk](), [soc](), [usb](), [video](), [xilinx-zynq]() ### AI overview CNX Software reports on Circuit Valley's CHC5, a modular camera system built around an AMD/Xilinx Zynq-7020 SoC FPGA. It supports interchangeable sensor and lens configurations, USB, HDMI, and Gigabit Ethernet interfaces, and image-processing and machine-vision workloads. ### Source excerpt Circuit Valley's CHC5 is a modular camera system based on a Core board powered by an AMD/Xilinx Zynq-7020 SoC FPGA, a range of interface boards with USB, HDMI, or Ethernet (PoE), various sensor boards, and a metal enclosure. The solution can be customized with different lens objectives and different sensors with MIPI D-PHY, LVDS, Sub-LVDS, Low Voltage LVDS, or SLVS interfaces. The Zynq-7020's Cortex-A9 cores can handle complex tasks, while the FPGA fabric takes care of high-speed calculation and correction on the image, and can also be leveraged for AI/machine-vision-specific algorithms or complex low-latency hardware acceleration. CHC5 specifications: Core board SoC - Xilinx AMD Zynq-7020 SoC FPGA CPU - Dual-core Arm Cortex-A9 processor FPGA - 85K logic cells, 4.9Mb Block RAM, 220 DSP slices System Memory - 1GB DDR3 Storage 1 Gbit flash memory MicroSD card slot ISP - Full-fledged ISP implemented on FPGA fabric Multiple interface boards with 10Gbps [...] The post Circuit Valley CHC5 - A modular USB, HDMI, and Ethernet camera system (Crowdfunding) appeared first on CNX Software - Embedded Systems News. ## Best Raspberry Pi Camera: Which Model Is Right for You? DevFeed: [Best Raspberry Pi Camera: Which Model Is Right for You?]() Original publisher: [Read original article]() Author: Karen Rangi Published: 2026-08-29T05:00:00Z Content type: comparison Language: en Sources: [RaspberryTips]() Topics: [webcam]() Tags: [article](), [inspiration](), [raspberry-pi]() ### AI overview A comparison of official Raspberry Pi cameras that recommends the Raspberry Pi Camera Module 3 for most everyday projects while explaining the intended uses of the High Quality, AI, and Global Shutter cameras. ### Source excerpt I thought this would be an easy article to write. "Which Raspberry Pi camera should you buy?" used to have a simple answer. Today, the Raspberry Pi Foundation has several official models, each built for a different purpose. I spent some time comparing them all, so you don't have to. In most cases, the Raspberry... ## How to Live Stream the Raspberry Pi Camera (2 Easy Ways) DevFeed: [How to Live Stream the Raspberry Pi Camera (2 Easy Ways)]() Original publisher: [Read original article]() Author: Dhairya Parikh Published: 2026-08-27T04:21:36Z Content type: tutorial Language: en Sources: [RaspberryTips]() Topics: [Streaming](), [webcam](), [real-time](), [Protocol (disambiguation)](), [Hardware](), [Web](), [Linux](), [Terminal](), [Software]() Tags: [guide](), [hardware](), [how-to](), [how-to-tutorials](), [linux](), [live-stream](), [process](), [raspberry-pi](), [raspberry-pi-os](), [real-time](), [software](), [streaming](), [video](), [web]() ### AI overview A tutorial explaining two ways to live-stream video from a Raspberry Pi Camera to another device: using an RTSP stream or a web page on the local network. It covers the required Raspberry Pi hardware, camera module, SD card, Raspberry Pi OS, and the initial terminal command for starting an RTSP stream. ### Source excerpt I've used Raspberry Pi cameras in many projects over the years, and live streaming is one of those features that sounds more complicated than it really is. Once the camera is working, there are a few simple ways to stream its feed to another device. Raspberry Pi Camera video can be live-streamed in two ways:... ## CodeScanner.scan(): Barcode Scanning Without Rebuilding the Camera Pipeline DevFeed: [CodeScanner.scan(): Barcode Scanning Without Rebuilding the Camera Pipeline]() Original publisher: [Read original article]() Author: Shai Almog Published: 2026-08-26T00:00:00Z Content type: release Language: en Sources: [CodeName One]() Topics: [Barcode](), [QR Code](), [webcam](), [Code]() Tags: [camera](), [code](), [component](), [on-device](), [pipeline](), [vision]() ### AI overview Codename One adds CodeScanner and VisionCameraView, higher-level APIs for full-screen barcode scanning and embedded live vision analysis. The update also introduces typed results, coordinate helpers, image bridging, and analyzer-specific native dependency selection. ### Source excerpt CodeScanner and VisionCameraView put full-screen scanning and embedded live analysis above Codename One's on-device vision APIs, with typed results and simulator scripting. ## Towards passive heart health monitoring via smartphone camera DevFeed: [Towards passive heart health monitoring via smartphone camera]() Original publisher: [Read original article]() Published: 2026-06-04T19:47:00Z Content type: article Language: en Sources: [The latest research from Google]() Topics: [Monitoring](), [webcam](), [dataset](), [Deep learning](), [Google](), [Ground truth / benchmark quality]() Tags: [deep-learning](), [devices](), [google](), [health](), [health-bioscience](), [heart-rate-monitoring](), [human-computer-interaction-and-visualization](), [machine-intelligence](), [model](), [monitoring](), [publication](), [research](), [resource](), [smartphones]() ### AI overview Google Research presents PHRM, a research system that passively estimates heart rate and resting heart rate from facial video captured by a smartphone's front-facing camera during everyday use. The system applies deep learning to video recorded after face unlock events and reports accuracy comparable to electrocardiogram-derived ground truth and wearable trackers. The publication also releases a large, diverse smartphone-video dataset and the pre-trained PHRM-mini model for qualified researchers. ### Source excerpt Health & Bioscience ## Building a Magic Mirror: AI retail experiences with Remix DevFeed: [Building a Magic Mirror: AI retail experiences with Remix]() Original publisher: [Read original article]() Author: Nikola Draca Published: 2026-03-19T12:33:46Z Content type: article Language: en Sources: [Shopify Engineering](), [Shopify Engineering - Shopify Engineering]() Topics: [Artificial Intelligence](), [Remix](), [webcam](), [Shopify](), [browser](), [API]() Tags: [ai](), [api](), [browser](), [building](), [code](), [customer](), [generate](), [how-to](), [mirror](), [product](), [retail](), [server](), [shopify](), [webcam]() ### AI overview This article presents Shopify's AI-powered magic mirror: a customizable retail installation that uses a display, hidden webcam, and Remix server to recognize visual signals and deliver personalized messages, animations, product recommendations, challenges, and discount codes. It also outlines a makeup shade-matching use case and the hardware needed to build the experience. ### Source excerpt The technical blueprint for an AI-powered mirror that sees customers, analyzes their appearance, and delivers personalized product recommendations in real-time. ## Analysis of Dahua CCTV Camera Authentication DevFeed: [Analysis of Dahua CCTV Camera Authentication]() Original publisher: [Read original article]() Published: 2025-12-01T23:00:00Z Content type: tutorial Language: en Sources: [Dennis Yurichev]() Topics: [webcam](), [hash](), [Python]() Tags: [auth](), [camera](), [hash](), [python](), [tcp]() ### AI overview A pentesting-oriented analysis of Dahua CCTV camera authentication over its proprietary TCP protocol. It describes a fake Python server used to observe a camera login and presents the known portion of the hash calculation, while noting that the remaining 16 bytes are not understood and no Hashcat workflow was found. ### Source excerpt [Pentesting] Dahua (CCTV cameras) auth ## A look at a P2P camera (LookCam app) DevFeed: [A look at a P2P camera (LookCam app)]() Original publisher: [Read original article]() Author: Wladimir Palant Published: 2025-09-08T13:00:50Z Content type: article Language: en Sources: [Almost Secure]() Topics: [Security](), [Vulnerabilities](), [webcam](), [Encryption](), [P2P](), [Cloud]() Tags: [camera](), [cloud](), [encryption](), [internet](), [p2p](), [security]() ### AI overview A security analysis of internet-connected cameras managed through the LookCam app reports weak access controls, largely unencrypted PPPP communication, exposed cloud uploads, firmware security flaws, and no firmware update mechanism. The findings are presented as applying to LookCam-managed cameras and several related apps, but not LookCamPro devices. ### Source excerpt I've got my hands on an internet-connected camera and decided to take a closer look, having already read about security issues with similar cameras. What I found far exceeded my expectations: fake access controls, bogus protocol encryption, completely unprotected cloud uploads and firmware riddled with security flaws. One could even say that these cameras are Murphy's Law turned solid: everything that could be done wrong has been done wrong here. While there is considerable prior research on these and similar cameras that outlines some of the flaws, I felt that the combination of severe flaws is reason enough to publish an article of my own. My findings should apply to any camera that can be managed via the LookCam app. This includes cameras meant to be used with less popular apps of the same developer: tcam, CloudWayCam, VDP, AIBoxcam, IP System. Note that the LookCamPro app, while visually very similar, is technically quite different. It also uses the PPPP protocol for low-level communication but otherwise doesn't seem to be related, and the corresponding devices are unlikely to suffer from the same flaws. There seems to be little chance that things will improve with these cameras. I have no way of contacting either the hardware vendors or the developers behind the LookCam app. In fact, it looks like masking their identity was done on purpose here. But even if I could contact them, the cameras lack an update mechanism for their firmware. So fixing the devices already sold is impossible. I have no way of knowing how many of these cameras exist. The LookCam app is currently listed with almost 1.5 million downloads on Google Play however. An iPhone and a Windows version of the app are also available but no public statistics exist here. Contents The highlights The hardware The LookCam app The PPPP protocol The basics The "encryption" The threat model The firmware The cloud How safe are device IDs? Recommendations Further reading The highlights The camera cannot be eas ## How to make the iPhone Continuity Camera work properly in Chrome DevFeed: [How to make the iPhone Continuity Camera work properly in Chrome]() Original publisher: [Read original article]() Author: Kaushik Gopal Published: 2024-12-12T07:00:00Z Content type: tutorial Language: en Sources: [Kaushik Gopal's Site]() Topics: [iphone](), [Chrome](), [webcam](), [macOS](), [Google Meet](), [Chromium](), [browser](), [Mobile]() Tags: [android](), [camera](), [chrome](), [google](), [how-to](), [iphone](), [macos](), [webcam]() ### AI overview A practical guide explains how to make an iPhone using Continuity Camera appear as a webcam in Google Meet on Chromium browsers. The phone must be in landscape mode, have its screen off, be locked and motionless, and have an unobstructed camera. ### Source excerpt I use a pixel as my primary android phone. But as a mobile developer, I also keep an iPhone handy for those times I need to test how an app works on iOS (especially if it's not available on Android1). But my iPhone doesn't sit in a drawer unused. It doubles up as my webcam when not being used as a phone. This is possible because I use macOS for my primary desktop needs, and this wonderful feature it enables called "Continuity Camera". I've removed a webcam from my setup thanks to this, and the camera actually works much better than most webcams out there today. But there's one really annoying thing about this setup. It won't be recognized in Google Meet when using a chromium browser. Searching on Reddit points out that this is a bizzarre known security requirement for chromium browsers alone. Your iPhone needs: to be in landscape mode (so don't have portrait lock on) have the screen turned off to be locked motionless (so won't work if handheld) and have an unobstructed camera wut 😵💫 But works like a charm. So if you run into this issue, fix those things and it'll all work like a charm. thinking about you Flighty. ↩︎ ## November 2024 Pine64 Community Update Introduces the PineCam and Covers Other Projects DevFeed: [November 2024 Pine64 Community Update Introduces the PineCam and Covers Other Projects]() Original publisher: [Read original article]() Published: 2024-11-21T00:00:00Z Content type: article Language: en Sources: [Community blog on PINE64]() Topics: [Hardware](), [Single Board Computer](), [SOC](), [RISC-V](), [Linux](), [webcam](), [Specifications]() Tags: [avaota-a1](), [camera](), [community-update](), [hardware](), [linux](), [ox64](), [pinecam](), [pinedio](), [pinenote](), [pinetab-v](), [risc-v](), [single-board-computer](), [soc](), [specifications](), [usb]() ### AI overview Pine64's November 2024 community update introduces the PineCam, a successor to the PineCube based on the Oz64 single-board computer and SG2000 SoC. It also provides updates on other Pine64 projects and community activities. ### Source excerpt Welcome back to a new monthly Pine64 community update! This month we are announcing a couple of new products including a SBC and a successor to the PineCube. We have updates to share about the PineNote and the PineDio USB adapter this month along with a talk by one of our community members Dsimic. Table of contents PineCam Yuzuki Avaota-A1 PineNote Attention to all users who have ordered/received a PineNote For general users wanting to purchase a PineNote PineNote News PineTab-V BarCamp Talk About Pine64 and Ox64 Handout PineDio Community content Monthly community updates Want to contribute to the next community update? PineCam Authors: Lukasz, Caffeine The first new device we will be introducing this update is the PineCam! The PineCam is a successor to the PineCube IP camera, but with a much more polished design, better specifications and more features. While the PineCube didn't achieve the success the project had hoped for, we believe it wasn't due to a lack of interest in such hardware, but rather the way it was executed. We've gathered feedback, learned from what went wrong, and have gone back to the drawing board. This time, the PineStore have decided to take a different approach, using a System-on-Chip (SoC) already in our hardware lineup. The device includes more RAM (compared to the PineCube's 128MB), and utilizes a camera interface that "just works". The PineCam is based on the oz64 single board computer which is powered by the SG2000 system on a chip found in the new Oz64. The SOC includes two RISC-V cores (C906 @1Ghz + C906 @700Mhz) and one ARM core (Cortex-A53 @1Ghz). You can find more information on the specifications of the Oz64 and the SOC it's using here. The device features 512MB of RAM, providing just enough memory to run a full Linux-based OS such as MotionEyeOS, a popular surveillance camera operating system. Specific to the PineCam now, the device includes a 2MP camera module which is the same one found in the PineTab 2/-V (the GalaxyCore GC02M2 ## Review of Continuity Camera as an iPhone Webcam DevFeed: [Review of Continuity Camera as an iPhone Webcam]() Original publisher: [Read original article]() Author: Carlos Alexandro Becker Published: 2024-10-11T00:00:00Z Content type: opinion Language: en Sources: [Carlos Becker]() Topics: [webcam](), [iphone](), [macOS]() Tags: [camera](), [iphone](), [macos](), [magsafe](), [webcam]() ### AI overview A short review of macOS Continuity Camera for using an iPhone as a webcam. The author values its wireless convenience and image and sound quality, but reports an initial disconnection, substantial battery drain, and phone heating during meetings. ### Source excerpt Continuity Camera is the macOS feature that allows you to use an iPhone as a webcam. ## Webcam randomly pausing in OBS, Discord, and websites - LSVCam and TikTok Studio DevFeed: [Webcam randomly pausing in OBS, Discord, and websites - LSVCam and TikTok Studio]() Original publisher: [Read original article]() Author: Scott Hanselman Published: 2024-10-09T19:32:28Z Content type: article Language: en Sources: [Scott Hanselman]() Topics: [webcam](), [Windows](), [browser](), [PowerShell](), [Streaming]() Tags: [browser](), [bugs](), [powershell](), [streaming](), [webcam](), [windows]() ### AI overview A troubleshooting account of webcam streams pausing in OBS and browser-based applications. The article investigates virtual cameras on Windows, identifies LSVCam as a possible source of enumeration hangs, and describes a registry location where it appears. ### Source excerpt I use my webcam constantly for streaming and I'm pretty familiar with all the internals and how the camera model on Windows works. I also use OBS extensively, so I regularly use the OBS virtual camera and flow everything through Open Broadcasting Studio. For my podcast, I use Zencastr which is a web-based app that talks to the webcam via the browser APIs. For YouTubes, I'll use Riverside or StreamYard, also webapps. I've done this reliably for the last several years without any trouble. Yesterday, I started seeing the most weird thing and it was absolutely perplexing and almost destroyed the day. I started seeing regular pauses in my webcam stream but only in two instances. The webcam would pause for 10-15 seconds every 90 or so seconds when access the Webcam in a browser I would see a long pause/hang in OBS when double clicking on my Video Source (Webcam) to view its properties Micah initially said USB but my usb bus and hubs have worked reliably for years. Thought something might have changed in my El Gato capture device, but that has also been rock solid for 1/2 a decade. Then I started exploring virtual cameras and looked in the windows camera dialog under settings for a list of all virtual cameras. Interestingly, virtual cameras don't get listed under Cameras in Settings in Windows: From what I can tell, there's no user interface to list out all of your cameras - virtual or otherwise - in windows. Here's a quick PowerShell script you can run to list out anything 'connected' that also includes the string "cam" in your local devices Get-CimInstance -Namespace root\cimv2 -ClassName Win32_PnPEntity | Where-Object { $_.Name -match 'Cam' } | Select-Object Name, Manufacturer, PNPDeviceID and my output Name Manufacturer PNPDeviceID ---- ------------ ----------- Cam Link 4K Microsoft USB\VID_0FD9&PID_0066&MI_00\7&3768531A&0&0000 Digital Audio Interface (2- Cam Link 4K) Microsoft SWD\MMDEVAPI\{0.0.1.00000000}.{AF1690B6-CA2A-4AD3-AAFD-8DDEBB83DD4A} Logitech StreamCam WinU ## Scrypted Connects Cameras to Home Hubs DevFeed: [Scrypted Connects Cameras to Home Hubs]() Original publisher: [Read original article]() Author: Techno Tim Published: 2023-05-13T15:00:00Z Content type: tutorial Language: en Sources: [Techno Tim]() Topics: [Home Assistant](), [webcam](), [Open Source](), [Automation]() Tags: [alexa](), [automation](), [camera](), [devices](), [google-home](), [home-assistant](), [homekit](), [hub](), [integration](), [open-source](), [self-hosted](), [stream](), [unifi](), [unifi-cameras]() ### AI overview This article presents Scrypted, open source software hosted on a local machine that connects cameras from various manufacturers to home hubs such as Apple HomeKit, Google Home, Alexa, and Home Assistant. It describes how this can enable hub features including notifications and automation without replacing existing cameras. ### Source excerpt Meet Scrypted an Open Source app that will let you connect almost any camera to any home hub, certified or not! You can connect popular devices from UniFi, Amcrest, Hikvision, Nest & Google, Tuya, Reolink, and many others to your home hub of choice, whether that be Apple's HomeKit, Google Home, Alexa, or even Home Assistant.This lets you choose and reuse your own devices and take advantage... ## RAD Chat Room - Part 5 DevFeed: [RAD Chat Room - Part 5]() Original publisher: [Read original article]() Author: Steve Hannah Published: 2020-05-28T00:00:00Z Content type: tutorial Language: en Sources: [CodeName One]() Topics: [Tutorial](), [Messaging](), [ui](), [mvc](), [Back end](), [webcam](), [WebSocket]() Tags: [architecture](), [back-end](), [camera](), [capture](), [library](), [messaging](), [mvc](), [tutorial]() ### AI overview Part 5 of a RAD Chatroom tutorial adds a capturePhoto action that lets users select or take an image and insert it into a chat message. It also explains that the mock application has no server integration and recommends the cn1-websockets library as a starting point. ### Source excerpt This is part 5 of the RAD Chatroom tutorial. You can find part 1 here, part 2 here, part 3 here and part 4 here. Adding A Photo Capture Feature Most messaging applications include the ability to add photos to messages. Let's add this feature to our chat app now. First we'll define a new action called "capturePhoto", and add to the TEXT_ACTIONS category of our view node. public static final ActionNode capturePhoto = action( icon(FontImage.MATERIAL_CAMERA) ); ... ViewNode viewNode = new ViewNode( actions(ChatRoomView.SEND_ACTION, send), actions(ProfileAvatarView.PROFILE_AVATAR_CLICKED_MENU, phone, videoConference), actions(ChatBubbleView.CHAT_BUBBLE_LONG_PRESS_MENU, likeAction), actions(ChatBubbleView.CHAT_BUBBLE_BADGES, likedBadge), actions(ChatRoomView.TEXT_ACTIONS, capturePhoto) __**(1)** ); __1 Added capturePhoto action to the TEXT_ACTIONS category so that it will appear as a button beside the text field. And we'll also add a handler for this action, which will capture a photo, and embed the photo in a message that we will add to the chat room's view model. ## SLR as a Webcam DevFeed: [SLR as a Webcam]() Original publisher: [Read original article]() Author: Adam Published: 2020-05-28T00:00:00Z Content type: opinion Language: en Sources: [Shostack & Friends Blog]() Topics: [webcam](), [hdmi](), [zoom](), [macOS]() Tags: [camera](), [hdmi](), [macos](), [webcam](), [zoom]() ### AI overview This personal technical account explores using an SLR camera as a webcam for Zoom without an HDMI capture card. It discusses Camera Live, CamTwist, iGlasses, and a macOS codesign command, while noting that the workaround affected Zoom microphone access and required downgrading Zoom. ### Source excerpt As I built out my home studio to record videos for my distributed classes, I was lucky enough to be able to find an in-stock HDMI capture card, but those are harder and harder to find. As it turns out, you may be able to avoid the need for that with a mix of apps. ## Setup and Best Settings for Streamlabs OBS on Mac DevFeed: [Setup and Best Settings for Streamlabs OBS on Mac]() Original publisher: [Read original article]() Author: Techno Tim Published: 2020-05-09T14:00:00Z Content type: tutorial Language: en Sources: [Techno Tim]() Topics: [Streaming](), [macOS](), [webcam](), [Hardware]() Tags: [audio](), [capture](), [desktop](), [hardware](), [install](), [layout](), [mac](), [macos](), [quick-start](), [repo](), [source](), [streaming](), [video](), [webcam]() ### AI overview A video tutorial explains how to set up Streamlabs OBS on macOS, including desktop audio capture with iShowU Audio Capture, webcam and game capture with a Cam Link, alerts, streaming settings, layout, and going live. ### Source excerpt Streamlabs OBS for MacOS is here! In this video we'll walk through setting up Streamlabs step by step.We'll install Streamlabs OBS, set up desktop audio with iShowU Audio Capture so you can capture desktop audio, configure our webcam and game capture with a Cam Link, set up our alerts, configure the best possible streaming settings for Streamlabs, adjust our streaming layout, and go live. 📺... ## Video Capture Constraints DevFeed: [Video Capture Constraints]() Original publisher: [Read original article]() Author: Steve Hannah Published: 2019-03-12T00:00:00Z Content type: article Language: en Sources: [CodeName One]() Topics: [API](), [webcam](), [Web Development]() Tags: [api](), [capture](), [component](), [layout](), [platform](), [quality](), [video]() ### AI overview This article explains a video capture constraints API for specifying preferred video quality, maximum duration, maximum file size, and resolution. It describes runtime support checks and notes that constraint support varies by platform and device. ### Source excerpt The new video capture constraints API allows you to specify "constraints" when capturing videos. Constraints include: Video Quality (High or Low) Maximum duration Maximum file size Video Resolution (i.e. width and height). Support for these constraints varies by platform and device, but the API allows you to check if your constraints are supported at runtime. Essentially, you set your "preferred" constraints, and the API will give you its best attempt at meeting those constraints. This is similar to setting a visual Component's preferred width and height. The layout manager takes these preferred dimensions under advisement, but ultimately sets the size on its own. ## How we wrote chicken egg counter on a Raspberry PI DevFeed: [How we wrote chicken egg counter on a Raspberry PI]() Original publisher: [Read original article]() Author: Ivan Ursul Published: 2018-10-03T09:23:24Z Content type: tutorial Language: en Sources: [Ivan Ursul]() Topics: [Raspberry Pi](), [OpenCV](), [webcam](), [Linux](), [Databases]() Tags: [camera](), [image-recognition](), [java](), [linux](), [migrations](), [mongodb](), [network](), [raspberry-pi](), [stream](), [webcam]() ### AI overview A project account describing the design of a Raspberry Pi application that uses a webcam and OpenCV-based image recognition to count chicken eggs on a factory conveyor and send the count to a database. It discusses tracking eggs across camera frames and preprocessing images to identify contours and ellipses. ### Source excerpt How it started Besides my main work on Upwork I quite often pick different projets. So I found a project, where I had to write a program for recognizing chicken eggs on a factory stream line. Customer wanted to install the application on computer with web camera, put this camera at a top of stream line and the application had to calculate eggs and send them to the DB. He also wanted to run this program on a cheap computer. The quality of the network in the factory isn't stable, so the program had to be resilient to outstand the network issues. There was enough challenges for me, so I decided to participate on this project. [Next page]()